WNDR3700v3

The Netgear WNDR3700v3 router has 300mbps WiFi, 4 N/A ETH-ports and 0 USB-ports.

Quick links:
Default password/Login
Login instructions
User Manuals

WNDR3700v3 router specifications (specs)

System specs
CPU: n/a
RAM: 64 MiB
Flash: 8 MiB
Custom firmwares: None

Connectivity
WiFi: 300mbps (abgn)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: 1 x N/A port
ETH: 4 x N/A ports
USB-ports: 0

Hard reset instructions for Netgear WNDR3700v3

If your WNDR3700v3 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Netgear WNDR3700v3 in the following way(s):

With the reset button

Have the router powered on (if just booted wait around one minute for it to load)
With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds
When the power light starts to blink you can release the reset button and wait for the router to start up
The power light will be solid (not blinking) once the router is started.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:

When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Netgear WNDR3700v3

If you have performed a reset of your WNDR3700v3 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 192.168.1.1 Netgear login instructions
Default username: admin Netgear router default password list
Default password: password
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

To login to the WNDR3700v3 router and change the settings, you can follow these steps:

Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
Open your browser and visit http://192.168.1.1
You should be prompted with a login dialogue.
Enter the username: admin and the password password
Note: If you have already changed the password use that instead.
You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Netgear credentials, as they can usually be shared across models/variants.

WNDR3700v3 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Netgear WNDR3700v3:

Netgear stock firmware for the WNDR3700v3

Stock firmwares for the WNDR3700v3 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.