WRVS4400N v2.0
Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0

Thumbnail for the Linksys WRVS4400N v2.0 router with 300mbps WiFi, 4 N/A ETH-ports and
0 USB-ports

The Linksys WRVS4400N v2.0 router has 300mbps WiFi, 4 N/A ETH-ports and 0 USB-ports.
It is also known as the Linksys Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0.

Quick links:
Default password/Login
Login instructions
User Manuals

WRVS4400N v2.0 router specifications (specs)

System specs
CPU: 250 MHz + 250 MHz
RAM: 64 MiB + 16 MiB
Flash: 8 MiB
Custom firmwares: OpenWrt

Connectivity
WiFi: 300mbps (bgn)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: 1 x N/A port
ETH: 4 x N/A ports
USB-ports: 0

Hard reset instructions for Linksys WRVS4400N v2.0

If your WRVS4400N v2.0 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Linksys WRVS4400N v2.0 in the following way(s):

Through the web interface

Open your browser and navigate to the router interface (check default settings below)
Under the Administration tab you will find a sub-tab called Factory defaults
On the Factory defaults page click the button labeled Restore Factory Defaults

With the reset button

Have your unit powered on
Press and hold the reset button for at least 10 seconds until the power light starts blinking, then release.
When the power light goes solid, unplug the power to the router for 10 seconds
Plug the power back in and start the router
When the power light goes solid again the router is ready to use.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:

When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Linksys WRVS4400N v2.0

If you have performed a reset of your WRVS4400N v2.0 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 192.168.1.1 Linksys login instructions
Default username: admin Linksys router default password list
Default password: admin
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

To login to the Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 and change the settings, you can follow these steps:

Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
Open your browser and visit http://192.168.1.1
You should be prompted with a login dialogue.
Enter the username: admin and the password admin
Note: If you have already changed the password use that instead.
You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Linksys credentials, as they can usually be shared across models/variants.