WZR-HP-AG300H

The Buffalo WZR-HP-AG300H router has 300mbps WiFi, 4 N/A ETH-ports and 0 USB-ports. It also supports custom firmwares like: dd-wrt, OpenWrt

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares

WZR-HP-AG300H router specifications (specs)

Buffalo WZR-HP-AG300H review (quick overview)

Here is the quick comparison of how the Buffalo WZR-HP-AG300H compares to other routers on our site:

Hard reset instructions for Buffalo WZR-HP-AG300H

If your WZR-HP-AG300H router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Buffalo WZR-HP-AG300H in the following way(s):

The 30-30-30 reset

1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Buffalo WZR-HP-AG300H

How to login to the WZR-HP-AG300H

To login to the WZR-HP-AG300H router and change the settings, you can follow these steps:

1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
2. Open your browser and visit http://192.168.11.1
3. You should be prompted with a login dialogue.
4. Enter the username: root and the password password
   Note: If you have already changed the password use that instead.
5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Buffalo credentials, as they can usually be shared across models/variants.

WZR-HP-AG300H Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Buffalo WZR-HP-AG300H:

Flashing dd-wrt on the Buffalo WZR-HP-AG300H

Since the WZR-HP-AG300H has 32 MiB of flash memory, you should be able to run dd-wrt with full functionality without having to worry too much about which firmware to use.
Instructions on how to flash dd-wrt onto your Buffalo WZR-HP-AG300H can be found on the dd-wrt wiki
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Flashing OpenWrt on the Buffalo WZR-HP-AG300H

The Buffalo WZR-HP-AG300H is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
To get started with the flashing, head over to the OpenWrt instructions for WZR-HP-AG300H and they'll take it from there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Similar routers

WLAN-2202

CDW68AAM-U01

AIR-OEAP602I-A-K9

RT-N56U

DPC3848

RT-N56U B1