F9K1115 v2
AC1750 DB Wi-Fi Dual-Band AC+ Gigabit Router (F9K1115V2
The Belkin F9K1115 v2 router has Gigabit WiFi, 4 N/A ETH-ports and 0 USB-ports.
It is also known as the Belkin AC1750 DB Wi-Fi Dual-Band AC+ Gigabit Router (F9K1115V2.It also supports custom firmwares like: OpenWrt, LEDE Project
Quick links:
Default password/Login
User Manuals
Flashing Custom Firmwares
F9K1115 v2 router specifications (specs)
CPU: n/a
RAM: 128 MiB
Flash: 16 MiB
Custom firmwares: OpenWrt, LEDE Project
WiFi: Gigabit (abgn+ac)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: 1 x N/A port
ETH: 4 x N/A ports
USB-ports: 0
Belkin F9K1115 review (quick overview)
Here is the quick comparison of how the Belkin F9K1115 compares to other routers on our site:
For a full list of routers and how they compare to the F9K1115 v2, check the Router Buying Guide which will help you buy the most price-competitive router.
Hard reset instructions for Belkin F9K1115 v2
If your F9K1115 v2 router is not working as it should, dropping connections or not
being
responsive, you should first do a reset of the router to see if the problems persist. Other
scenarios where you might want to reset your router is if you've forgotten the password or
misconfigured it and can't get access anymore.
Your can reset your Belkin F9K1115 v2 in the following way(s):
The 30-30-30 reset
There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:- When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
- While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
- While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.
This process usually works for resetting any router to it's factory setting.
If that doesn't work be sure to check out the
questions and answers
incase someone else has had similar problems resetting their router.
Note: It is worth reading more about
how to reset routers with the 30 30 30 reset and what the risks and
considerations
are when resetting your router this way, instead of just rebooting it.
Default factory settings for Belkin F9K1115 v2
If you have performed a reset of your F9K1115 v2 device or not changed the defaults, you should be able to access it with the following settings:
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.2.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.
F9K1115 v2 Firmwares
Staying up to date with the latest firmware is a good idea to keep your router even more
secure
from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider
flashing
an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly
increase
the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Belkin F9K1115 v2:
Flashing OpenWrt on the Belkin F9K1115 v2
The Belkin F9K1115 v2 is supported by OpenWrt according to their Table of
Hardware. So
flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Belkin
F9K1115 v2, but since it's listed in their Table of Hardware as supported, you can
head
over to the
OpenWrt install instructions
and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to
read OpenWrt's wikis to understand the risks and how to proceed if something goes
wrong.
Flashing LEDE Project on the F9K1115 v2
The Belkin F9K1115 v2 is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their
Firmware downloads
page and
then follow the instructions on their
Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.
Report error on page
(If info is incorrect)
