MI424WR rev C

The Actiontec MI424WR rev C router has 54mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports. It also supports custom firmwares like: dd-wrt, OpenWrt, LEDE Project

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares

MI424WR rev C router specifications (specs)

Hard reset instructions for Actiontec MI424WR rev C

If your MI424WR rev C router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Actiontec MI424WR rev C in the following way(s):

The 30-30-30 reset

1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Actiontec MI424WR rev C

How to login to the MI424WR rev C

To login to the MI424WR rev C router and change the settings, you can follow these steps:

1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
2. Open your browser and visit http://192.168.1.1
3. You should be prompted with a login dialogue.
4. Enter the username: admin and the password ''unit's serial number''
   Note: If you have already changed the password use that instead.
5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Actiontec credentials, as they can usually be shared across models/variants.

MI424WR rev C Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Actiontec MI424WR rev C:

Flashing dd-wrt on the Actiontec MI424WR rev C

Instructions on how to flash dd-wrt onto your Actiontec MI424WR rev C can be found on the dd-wrt wiki
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Flashing OpenWrt on the Actiontec MI424WR rev C

The Actiontec MI424WR rev C is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
To get started with the flashing, head over to the OpenWrt instructions for MI424WR rev C and they'll take it from there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Flashing LEDE Project on the MI424WR rev C

The Actiontec MI424WR rev C is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their Firmware downloads page and then follow the instructions on their Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.

Similar routers

MI424WR rev D

2700HG-B

MI424WR rev E

2700HGV

PK5000 (Qwest)

2701HG-B