WAP2102

The AboCom WAP2102 router has 54mbps WiFi, 1 100mbps ETH-ports and 0 USB-ports. It also supports custom firmwares like: dd-wrt

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares

WAP2102 router specifications (specs)

System specs
CPU: n/a
RAM: 16 MiB
Flash: 4 MiB
Custom firmwares: dd-wrt

Connectivity
WiFi: 54mbps (bg)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: None
ETH: 1 x 100mbps port
USB-ports: 0

Hard reset instructions for AboCom WAP2102

If your WAP2102 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your AboCom WAP2102 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:

When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for AboCom WAP2102

If you have performed a reset of your WAP2102 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 192.168.1.254 AboCom login instructions
Default username: admin AboCom router default password list
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.254
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

To login to the WAP2102 router and change the settings, you can follow these steps:

Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
Open your browser and visit http://192.168.1.254
You should be prompted with a login dialogue.
Enter the username: admin and if it requires a password, leave it empty or try with admin/password
Note: If you have already changed the password use that instead.
You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common AboCom credentials, as they can usually be shared across models/variants.

WAP2102 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the AboCom WAP2102:

Flashing dd-wrt on the AboCom WAP2102

Since the WAP2102 has 4 MiB of flash memory, you should choose a stripped down version of dd-wrt that fits on the smaller flash. We haven't find any specific instructions for flashin dd-wrt onto the AboCom WAP2102, but you can read the Installation guide over at dd-wrt to get a clue on how to proceed (As this model is listed as supported).
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.