RouterBOARD hAP lite (RB941-2nD-TC)
MikroTik hAP lite - Home Access Point

The MikroTik RouterBOARD hAP lite (RB941-2nD-TC) router has 300mbps WiFi, 3 100mbps ETH-ports and 0 USB-ports.
It is also known as the MikroTik MikroTik hAP lite - Home Access Point.It also supports custom firmwares like: LEDE Project

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares

RouterBOARD hAP lite (RB941-2nD-TC) router specifications (specs)

MikroTik RouterBOARD hAP review (quick overview)

Here is the quick comparison of how the MikroTik RouterBOARD hAP compares to other routers on our site:

Hard reset instructions for MikroTik RouterBOARD hAP lite (RB941-2nD-TC)

If your RouterBOARD hAP lite (RB941-2nD-TC) router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your MikroTik RouterBOARD hAP lite (RB941-2nD-TC) in the following way(s):

The 30-30-30 reset

1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for MikroTik RouterBOARD hAP lite (RB941-2nD-TC)

How to login to the RouterBOARD hAP lite (RB941-2nD-TC)

To login to the MikroTik hAP lite - Home Access Point and change the settings, you can follow these steps:

1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
2. Open your browser and visit http://192.168.88.1
3. You should be prompted with a login dialogue.
4. Enter the username: admin and if it requires a password, leave it empty or try with admin/password
   Note: If you have already changed the password use that instead.
5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common MikroTik credentials, as they can usually be shared across models/variants.

RouterBOARD hAP lite (RB941-2nD-TC) Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the MikroTik RouterBOARD hAP lite (RB941-2nD-TC):

Flashing LEDE Project on the RouterBOARD hAP lite (RB941-2nD-TC)

The MikroTik RouterBOARD hAP lite (RB941-2nD-TC) is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their Firmware downloads page and then follow the instructions on their Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.

Similar routers

Aterm WR8165N (ST)

Smart RG SR300NE

3G21WB

CG-WLR300NM

3G22WV

DHP-1320 rev A1