Pronghorn SBC250

The ADI Engineering Pronghorn SBC250 router has 54mbps WiFi, 2 100mbps ETH-ports and 0 USB-ports. It also supports custom firmwares like: OpenWrt, LEDE Project

Quick links:
Default password/Login
Login instructions
Flashing Custom Firmwares

Pronghorn SBC250 router specifications (specs)

Hard reset instructions for ADI Engineering Pronghorn SBC250

If your Pronghorn SBC250 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your ADI Engineering Pronghorn SBC250 in the following way(s):

The 30-30-30 reset

1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for ADI Engineering Pronghorn SBC250

How to login to the Pronghorn SBC250

To login to the Pronghorn SBC250 router and change the settings, you can follow these steps:

1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
2. Open your browser and visit http://192.168.1.1
3. You should be prompted with a login dialogue.
4. Enter the username: root and if it requires a password, leave it empty or try with admin/password
   Note: If you have already changed the password use that instead.
5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common ADI Engineering credentials, as they can usually be shared across models/variants.

Pronghorn SBC250 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the ADI Engineering Pronghorn SBC250:

Flashing OpenWrt on the ADI Engineering Pronghorn SBC250

The ADI Engineering Pronghorn SBC250 is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the ADI Engineering Pronghorn SBC250, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Flashing LEDE Project on the Pronghorn SBC250

The ADI Engineering Pronghorn SBC250 is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their Firmware downloads page and then follow the instructions on their Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.

Similar routers

AP-70

3100AG Access Point (BSP-AMAP3100AG)

DWL-7200AP

DWL-8200AP rev A1

DWL-8220AP rev A1

RBT-1602